Air-Cooled Pulse Laser Cleaning Machine MW-LY100 to 500: Low-Heat Cleaning for Thin Sheet, Molds and Precision Parts

The MAXWAVE MW-LY is an air-cooled pulse laser cleaning machine, 100 to 500 W, for mold shops, manufacturers and maintenance teams whose parts must keep their shape and finish.

Its 1064 nm pulses lift paint, oxide and light rust with little heat: thin panels stay flat, mold cavities need no abrasive contact.

Send a photo of the part and the layer on it, and an engineer tells you which MW-LY model fits.

  • 100 to 500 WPulsed fiber laser
  • AirCooled, no chiller, 220 V
  • 6Cleaning modes
  • 56 kgComplete machine on wheels
MAXWAVE MW-LY air-cooled pulse laser cleaning machine cabinet on wheels with the fiber and cleaning head stowed
Close-up of the MW-LY pulse laser cleaning head optics and protective lens
Double-swing head, quartz protective lens

Low Heat Input on Thin Sheet, Molds and Precision Parts

High precision, low heat, often called cold cleaning: matched to sensitive materials and thin layers.

Short pulses
Pulses of 13 to 500 ns at up to 3000 kHz (4000 kHz on the LY400 and LY500) vaporize the layer; the part cools between pulses.
Selective absorption
Paint, oxide and rust absorb 1064 nm far more than the metal beneath, so the layer comes off and the metal stays cool.
Pulse laser cleaned window of bare metal in the black coating of a thin sheet cover
Coating window on a sheet cover
Tire mold segment after pulse laser cleaning, fine ribs and edges intact
Tire mold ribs after pulsed cleaning

Sharp edges on both: cleaning stops where the scan stops, with no heat marks around it.

  • Thin sheetPanels and covers stay flat after paint or oxide removal; continuous-laser paint removal on sheet below 4 mm may distort them.
  • MoldsResidue and carbon come off with no media or brushes touching the cavity, so texture and edges stay as machined.
  • Precision and finished partsMachined faces and weld zones are cleaned without heat that shifts tolerances or leaves heat marks.
  • High-value componentsLow heat protects parts worth more than the cleaning time, including restoration work on metal, wood and stone.
  • Light rust on finished partsSurface rust comes off in two passes, leaving no loose powder.

Each pulse cleans a millimeter-to-centimeter spot: precise on edges and fine features, and the reason the MW-LY is not a heavy-rust machine.

Working Limits: Deep Rust and Large Areas

The MW-LY clears thin layers quickly. Thick rust is a different job: on deep rust the reference rate for the whole range is about 0.5 to 1 m²/h, so a bigger MW-LY does not become a heavy-rust machine.

If your daily work is heavy rust or thick paint on large steel surfaces over full shifts, that work belongs to the water-cooled CW laser cleaning machine.

Laser cleaning heavy rust from a structural steel I-beam
Heavy rust on structural steel: a job for the continuous line

Air cooling fits

Quick start with no water chiller beside the machine. Plants that move it between bays or sites, and work that comes in batches with breaks between them.

Water cooling fits

Long, steady shifts on thick parts. Both are compared on the pulsed vs CW laser cleaning machine page.

Work that mixes thin parts and heavy steel: we may quote one machine from each line.

Power Selection From LY100 to LY500

Choose power by the layer you remove and the part it sits on. Laser power on every MW-LY adjusts from 0 to 100%, so one machine also covers lighter jobs below its rating.

MW-LY power selection: scan field, frequency, reference cleaning figure and typical placement for each model group
ModelScan fieldFrequencyReference figureWhere we place it
MW-LY100 / LY200100 to 160 mm (by model)1 to 3000 kHzapprox. 5 to 8 m²/hPaint and coatingsPaint, coatings and thin films on small to medium parts, weld seams and detailed areas
MW-LY300100 to 160 mm (by model)1 to 3000 kHzapprox. 5 to 7 m²/hTypical example, mold cleaningMold cleaning and mixed workshop jobs
MW-LY400 / LY500100 to 160 mm (by model)1 to 4000 kHzapprox. 6 to 8 m²/hTypical example, LY500 coating removal on sheetCoating removal on larger sheet parts, where a wider field covers more surface per pass

How to use the figures: they come from our product data and real cleaning examples, and they shift with the substrate, layer thickness and settings. Use them to compare models, not as a promise for your part. For a figure on your own job, send the material, the layer and a photo.

Second choice

Pulsed laser source type

Tell us whether output or surface protection comes first, and the engineer confirms the source with your quote.

Output first

Single mode

For jobs where the paint removal rate is the priority. It removes paint more efficiently than multimode.

Surface first

Multimode

For finished parts, molds and delicate substrates that must take the least possible damage. Its cleaning rate is lower than single mode.

MW-LY cabinet main rotary switch above a cooling fan grille
Main switch and cabinet fan
MW-LY rear panel with supply connector, air inlet and the armored fiber leaving the cabinet
Rear panel, armored fiber exit

Cabinet Build and Electrical Details

Each detail is fitted to keep the machine running safely on a workshop floor.

Schneider electrical components
Relays, contactors and switching parts, so the machine starts and shuts down reliably.
6 mm² power cable
A heavy-section supply cable feeding the cabinet.
Three-color status light
Shows the three operating states, readable from across the bay.
Light and air-pressure alarms
A drop in air pressure to the head is flagged at once.
Two cooling fans
A fan on the laser source plus an external fan move heat out of the cabinet.
Automatic exit after 3 minutes idle
An unattended head is not left ready to fire.
Rounded cabinet corners
Fewer sharp edges for the people moving the cabinet around.
Armored fiber
A high-strength composite sheath protects the fiber as the cable is dragged and bent.

MW-LY Technical Specifications

Five models on one cabinet platform. The rows below are what changes from model to model.

MW-LY100 to MW-LY500 technical specifications by model
SpecificationMW-LY100MW-LY200MW-LY300MW-LY400MW-LY500
Average laser power100 W min.200 W min.300 W min.400 W min.500 W min.
Scan field100 to 160 mm, by model
Pulse frequency1 to 3000 kHz1 to 3000 kHz1 to 3000 kHz1 to 4000 kHz1 to 4000 kHz
Pulse width13 to 500 ns13 to 500 ns13 to 500 ns13 to 500 ns13 to 500 ns
Power instability<5%<5%<5%<5%<5%
Supply voltage220 V220 V220 V220 V220 V

Common to all five models

Laser
Pulsed fiber, 1064 nm, power adjustable 0 to 100%
Cooling
Air cooled
Cleaning modes
6
Machine size and weight
77×47×60 cm, 56 kg
Packed size and weight
83×65×75 cm, 71 kg
Cleaning head
0.9 kg
Side view of the MW-LY pulse laser cleaning machine with the cleaning head docked and fiber coiled on the hexagonal holder
56 kg · 77×47×60 cm

Typical Workshop Jobs for the MW-LY

Higher-intensity cleaning on parts brought to the cabinet at a repair bay or work station. Each job has its own page with process detail.

Vehicle door frame on a workshop stand, ready for pulsed laser cleaning along its frame and edges

Vehicle door frames

Paint and corrosion spots cleaned along frames and edges before repair, with the MW-LY cabinet parked beside the panel stand.

  • Laser clearing rust from a steel machine bracket

    Machinery repair parts

    Paint and light rust cleared from housings, guards and frames at the MW-LY work station during overhaul. Industrial maintenance

  • Alloy wheel hub after laser cleaning, bare metal on the spokes

    Wheel hubs

    Paint and surface rust removed from hubs brought to the MW-LY cabinet in the workshop.

  • Pulsed laser removing oxide from a fabricated metal part held in a vise

    Welded parts

    Oxide and heat tint removed from welds and the zone around them at an MW-LY station in the weld shop. Laser oxide removal

  • Laser beam removing a band of rust from a steel pipe

    Local rust removal

    Rust spots treated on steel parts at the work station before repainting, one area at a time. Laser rust removal

Delivery, Inspection and Operator Support

  • Tested before it ships

    Every MW-LY is assembled, commissioned and tested. See your unit on remote video or arrange a pre-shipment inspection; the process is on the About Us page.

  • Class 4 laser work

    Set up a controlled area with protection against reflections, and run fume extraction at the cleaning point.

  • Training and spare parts

    Training, site setup, laser safety, fume extraction and spare parts are on the support and maintenance page.

Send the part material and thickness, the layer to remove and a photo. An engineer replies with the MW-LY model that fits, or tells you if the job needs a different line.

Get a Quote for an MW-LY Pulse Laser Cleaner

Use the form to send your part and job details. An engineer replies with the MW-LY model and options that fit.

Five details for a model recommendation

  • Material and thickness: steel, stainless steel, aluminum, wood, stone or other.
  • Layer to remove: paint, coating, oxide, light rust or mold residue.
  • Workload: how much surface you clean per day or week.
  • Feature size: weld seams and mold details, or sheet and larger panels.
  • Photo: the part and the contamination. Photos can follow on WhatsApp.

Phone / WhatsApp: +86 15327155363 · Call