Industrial laser cleaning machine beam removing rust from a steel rebar, rusted steel left of the beam and cleaned steel right

Industrial Laser Cleaning Machines: Back to Bare Metal, No Media, No Solvents

MAXWAVE industrial laser cleaning machines remove rust, paint, coatings, oxide and process residue from metal parts, molds and machinery.

  • Built forFabrication plants, maintenance teams, surface preparation contractors, mold shops and OEM distributors
  • You getThe machine your part needs, not the biggest one on the list
  • HowMaterial, thickness and the layer to remove decide pulsed or continuous light, then the power level and the form factor for your workshop or job site
  • Pulsed fiber 1064 nm and continuous fiber 1080 nm
  • Four lines from 100 W pulsed to 6000 W continuous
  • Air-cooled and water-cooled options
  • Pre-shipment and remote video inspection

Before-and-After Results From Real Cleaning Jobs

Every pair is one real photograph of one surface: cleaned on one side, untouched on the other.

Rusted half of a steel plate before laser cleaning Laser cleaned half of the same steel plate after rust removal BeforeAfter
Black coated zone of a steel plate before laser coating removal Bare steel zone of the same plate after the laser cleaning machine removed the coating BeforeAfter
Oily mold half beside the laser cleaned halfBeforeAfter
Oil film on a mold
Grey coating next to the laser stripped metal surfaceAfterBefore
Grey coating on cast metal
Square steel bar rusted on one end and laser cleaned on the otherBeforeAfter
Rust on square bar
Steel plate with rusted lower zone and laser cleaned upper zoneAfterBefore
Heavy rust on plate
Drilled steel bar shown laser cleaned on the left and rusted on the rightAfterBefore
Rust and grime on a drilled bar
Cast aluminum housing, laser cleaned on the left and uncleaned on the right of the marked line
Cast aluminum housing
Read each pair forBase-metal colorNo residual powderClean edges

Both slider panels are cropped from that single photo. No speed or area figures come with them, because output depends on the layer, the machine and the settings.

All laser cleaning results by contamination and material

Rust, Paint, Oxide and Mold Residue: What Laser Cleaning Removes

The part under the layer decides which industrial laser cleaning machine fits, not the layer itself.

Industrial laser cleaning machine stripping rust from a steel I-beam sectionBefore

Rust and scale

Machined parts, frames, beams and heavy structures. On thin sheet, a pulsed unit removes rust in two passes and leaves no residual powder.

MW-LY / MW-LC pulsedMW-LCW heavy steel
Laser rust removal
Steel plate with black paint on one half and the laser cleaned bare steel on the otherBeforeAfter

Paint and coatings

Stripped from metal before repainting, inspection or repair, with no abrasive media and no solvents. Substrate thickness decides first.

Pulsed on thin sheetMW-LCW thick coatings
Laser coating removal
Pulsed laser cleaning oxide from a machined metal part held in a vise

Oxide and weld preparation

Oxide films, heat tint and weld discoloration on stainless, carbon steel and aluminum. Low heat input keeps the zone close to base-metal color.

Pulsed: standardCW: thick plate welds
Laser oxide removal
Mold housing with release agent and carbon residue before laser cleaning

Mold residue and oil

Release agent, rubber, carbon and oil, removed with no abrasive contact on the cavity. The deposit thickness decides the setup.

Pulsed cabinet or portable
Laser mold cleaning machine

On-site work on installed equipment: laser cleaning for industrial maintenance · all laser cleaning applications

Four Industrial Laser Cleaning Machine Lines

Pick the card that matches the part, then open the product page for the full parameter table.

MW-LY air-cooled pulsed laser cleaning machine cabinet on wheels

Air-cooled pulsedMW-LY100 / 200 / 300 / 400 / 500

Laser
Pulsed fiber, 1064 nm, air
Scan
100 to 160 mm
Supply
220 V

For thin sheet, precision parts, molds and high-value parts.

MW-LCW water-cooled continuous laser cleaner cabinet

Water-cooled continuousMW-LCW1500 to 6000

Laser
Continuous fiber, 1080 nm
Power
1500 to 6000 W
Stability
<1.5%

For thick plate, steel structures and large-area rust and paint over long shifts.

MW-LC trolley-case portable laser cleaner, case open with cleaning head

Trolley-case portableMW-LC100 / 200 / 300

Supply
24 V / 48 V
Scan
100 to 160 mm, 14 patterns
Head
Under 0.75 kg

For on-site repair and contract work, controlled from the handle or a phone.

MW-LC50D backpack laser cleaning machine with control screen and fiber hose

Backpack portableMW-LC50 series

Laser
Pulsed fiber, air
Builds
LC50D backpack, LC50B case
Specs
—

For work at height, tight spaces and thin layers in field maintenance.

All parameter tables: laser cleaning equipment overviewRobot or special-part system? Custom systems

Pulsed or Continuous Light, Matched to the Part

Pulsed light delivers energy in short bursts, so the part sheds heat between pulses. Continuous light delivers high output without a break, and thick steel absorbs the heat.

4 mm

Below 4 mm sheet, continuous paint removal may distort the panel. Thin guards and thick frames in one job can get both lines quoted.

FactorPoints to pulsedPoints to continuous
ThicknessThin sheet, no distortion allowedThick plate and structural steel
LayerOxide, heat tint, light rustHeavy rust, thick paint on large steel
PrecisionWeld zones, molds, edges, masked areasOpen, uniform surfaces
WorkloadOccasional parts and toolsLarge surfaces over full shifts
LocationWorkshop cabinet, or portable on siteWorkshop cabinet on a fixed supply

Full comparison: pulsed vs CW laser cleaning machine

Send a Photo of the Part

Material, thickness, contamination and one photo. An engineer replies with line, power level and options.

Get a Quote
PHONE / WHATSAPP +86 15327155363 Call now

Laser Cleaning Compared With Blasting, Chemicals and Grinding

The operating difference shows up in four places: what you buy, what you build around the job, what you throw away and what touches the part.

Laser cleaningAbrasive blastingChemical strippingGrinding
ConsumablesNo abrasive media, solvents or discsBlast mediaSolvents and strippersGrinding discs
Site preparationControlled laser area and fume extractionMedia containment and recoveryDip tanks or containmentDust control around the operator
WasteRemoved layer collected by the fume extractorSpent media to dispose ofUsed chemical to dispose ofSwarf and worn discs
Contact with the partNone: the beam does not touch the surfaceMedia impact on the surfaceChemical on the surfaceDisc wear on the surface
Laser cleaning a steel column on a fabrication line
Contractors weighing a switch from blasting: laser surface preparation for contractors

All four lines use fiber lasers and clean without touching the part.

  • 4machine lines
  • 6000Wtop power, from 100 W pulsed
  • 7systems behind every machine
  • 6final tests before shipment
  • 14scan patterns on MW-LC
  • <1.5%power stability on MW-LCW

About MAXWAVE: Industrial Laser Cleaning Equipment Supplier

Wuhan Maxwave Laser Technology Co., Ltd. supplies MAXWAVE laser cleaning machines to fabrication plants, maintenance teams, surface preparation contractors, mold shops and distributors.

  • Four lines, 100 W pulsed to 6000 W continuous
  • Machines, not cleaning services
  • Assembled, commissioned and tested in Wuhan, China
A machine matched to your part
Laser type and power sized to material, thickness and layer, not to the biggest wattage
See it working before it ships
Six final tests on every unit, with pre-shipment or remote video inspection
Parts that hold up in the plant
Quartz protective lenses, Schneider electrical components and Mean Well power supplies
Built to your part when standard won’t fit
Robot-assisted and train-wheel cleaning systems on record
Export-ready delivery
Cushioned, fixed packing, export documents and shipment tracking
Support for your exact unit
Spare parts and remote guidance matched to your configuration, see below

CE (Machinery Directive) attestations list the MAXWAVE laser cleaning machine models, and production runs under an ISO 9001 quality management system.

The company, its seven systems and certificates: About MAXWAVE
Technician assembling a laser cleaning machine on the assembly floor
Assembly and commissioning
Fluke thermal imager used to check laser cleaner components
Fluke thermal imager
Fujikura fiber cleaving and splicing equipment on the test bench
Fujikura fiber splicing
Schneider electrical components inside the laser cleaning machine cabinet
Schneider electrics
Quartz protective lenses for the laser cleaning head
Quartz protective lens

After-Sales Support for Your Operators

Support is built around the people running the machine, and around the exact unit they run.

Installation
Instructions ship with every machine
Operating tutorials
Walk operators through machine settings
Maintenance videos
Routine care of the machine, step by step
Troubleshooting
Remote engineering guidance from your photos and videos
Spare parts
Matched to your unit through the customer equipment records
Operator gripping the laser cleaner handheld head during training
Handheld head in use
Laser cleaning head with focusing optic for routine maintenance
Cleaning head optics

From Your Photo to a Machine Recommendation

Before an industrial laser cleaning machine is named, the material, its thickness and the layer are checked. This is what happens to your request.

  1. STEP 1

    You send the job

    Through the form below or WhatsApp, with a photo of the part.
  2. STEP 2

    An engineer reads it

    Pulsed or continuous, the power level and the form factor. Limits, such as rust the beam cannot reach, are flagged from the photos.
  3. STEP 3

    You get a configuration

    Line, power level and options, each with the reason. Before dispatch, the unit is shown on pre-shipment or remote video inspection.

Get a Quote for Your Cleaning Job

Send the requirement and an engineer recommends an industrial laser cleaning machine configuration: line, power level and options.

For a specific answer, include:

  • Material: steel, stainless steel, aluminum or other, with thickness
  • Contamination: rust, paint, coating, oxide, oil or residue
  • Area and workload: part size and surface cleaned per day or week
  • Application: production cleaning, maintenance, weld preparation, mold cleaning or contract work
  • Country: where the machine will be used
  • Photos of the part and the contaminated surface

Phone / WhatsApp: +86 15327155363 · Call