MAXWAVE Laser Cleaning Machine Supplier: See Your Machine Tested Before It Ships

MAXWAVE supplies pulsed and continuous fiber laser cleaning equipment, and shows you how each machine is built.

  • WhoFabrication plants, maintenance and repair companies, surface preparation contractors, mold shops, and distributors and OEM partners
  • WhyA laser cleaner has to keep working in your plant for years. How it is built matters as much as what it removes
  • InsideEach system that carries a machine from component to your workshop, and the documents behind it

From component to your workshop

Seven management systems covering the full product lifecycle, from development to after-sales.

  • CE attestationsMachinery Directive, models listed
  • ISO 9001Quality management system
  • Trademark 66902017MAXWAVE, held by the seller
  • Witnessed testsPre-shipment or remote video

Laser Cleaning Machine Supplier for Manufacturing and Maintenance

Wuhan Maxwave Laser Technology Co., Ltd. sells laser cleaning machines under its MAXWAVE brand: the equipment your operators use to remove rust, paint, coatings, oxide and process residue from metal parts, molds and machinery.

MAXWAVE sells machines and does not offer contract cleaning, so the work ends when your team runs the machine on its own parts. The time goes into components, assembly and commissioning, final tests, export packing and operator support.

  1. Your quoteIssued by Wuhan Maxwave Laser Technology
  2. CE attestationsSame holder, models listed
  3. ISO 9001Same company on the certificate
  4. Trademark66902017 registered to the seller
Every recommendation starts from your job. An engineer looks at the material, its thickness, the layer to remove and where the work happens, then names a line, a power level and the options that fit.
MAXWAVE laser cleaning machine supplier brand on the front of an MW-LCW continuous laser cleaning cabinet
MW-LCW cabinet with the MAXWAVE mark: the brand on the machine is the company on the quote.

Five Buyer Groups, One Inspection Standard

The range and the support are built for five kinds of buyer. Each gets the same machines, inspection and documents; the recommended configuration changes with the job.

  • Laser cleaning a bent steel bar corner on a fabrication floor

    Metal fabrication and manufacturing plants

    Cleaning parts before welding, coating or assembly, and removing oxide and heat tint after welding, on the production floor.

    Production line
  • Laser cleaning a wheel hub during maintenance and overhaul

    Maintenance and equipment repair companies

    Removing rust, paint and oil from machinery during repair and overhaul, often on the customer's site.

    Repair and overhaul
  • Contractor stripping rust from a steel pipe section with a laser cleaner

    Surface preparation contractors

    Carrying a portable unit from job to job and stripping rust and coatings on structures and equipment.

    Job to job
  • Rusted mold steel clamped in a vise before laser mold cleaning

    Mold shops

    Removing release agent, rubber and plastic residue and carbon deposits from molds without abrasive contact on the cavity.

    No abrasive contact
  • MAXWAVE branded trolley case laser cleaner sourced by distributors for resale

    Distributors and OEM partners

    Sourcing the range for resale in their own market, with configuration choices made together with MAXWAVE engineers.

    Resale

Four Laser Cleaning Lines in the MAXWAVE Range

Every line is built on a fiber laser source. Models, specifications and the full comparison sit on the equipment page; this is the short map.

MW-LY air-cooled pulsed laser cleaning machine cabinet

MW-LY air-cooled pulsed

Cabinet units, 100 to 500 W

MW-LY line
MW-LCW water-cooled continuous laser cleaning machine cabinet

MW-LCW water-cooled continuous

Cabinet units, 1500 to 6000 W

MW-LCW line
MW-LC trolley-case portable laser cleaner opened beside a technician

MW-LC trolley case

Portable, 24 V or 48 V supply

MW-LC line
MW-LC50 backpack laser cleaning machine with handheld head

MW-LC50 backpack

Work at height and in tight spaces

MW-LC50 line

R&D and Customization Built on Two Recorded Projects

Some parts do not fit a handheld or cabinet unit: the part is too large, the cleaning position is fixed, or cleaning has to happen inside a production line. For these jobs the system is designed around the part.

Project on record

Robot-assisted laser cleaning

A self-propelled robot paired with a laser cleaning machine.

Project on record

Large train-wheel cleaning equipment

A cleaning system built for large railway wheels.

To open a custom project, send:

  • The part's size and the layer to remove
  • The point in your process where cleaning has to happen
  • Photos of the part

The steps from requirement to delivered system are on the custom laser cleaning system page.

Specified laser cleaning head mounted on a MAXWAVE cabinet, the same head used in custom systems
A custom system runs through the same sequence as every standard machine: the same specified laser source, cleaning head and electrical system, the same assembly team and the same final tests. What changes is the mechanical side: how the head reaches the surface and how the system fits your line.

Component Supply and Manufacturing Control Behind Every Machine

Two of the seven systems sit inside the machine before any test is run: the core components that go into it and the fixed order it is built in. They show a plant buyer, or a distributor reselling the unit, what each machine is built from and how.

Protective Optics and a Lightweight Cleaning Head

How long a laser cleaner keeps working depends on a few parts. Five areas are specified for each line, and the first two sit right at the surface you clean.

Laser sourceCleaning headProtective opticsPower and electricalCabinet and structure
Laser cleaning head with its protective window facing the work surface
<0.75 kgMW-LC handheld cleaning head
Quartz protective lenses for the laser cleaning head
Quartz protective lenses
Faces
Fume, spatter, particles
Shields
Focusing optics
If damaged
Swap a spare lens

Protective optics

Every pass throws fume, spatter and particles toward the head. The protective lens takes that hit and shields the focusing optics behind it. A damaged protective lens is a spare part; damaged focusing optics take the head out of service.

Quartz protective lenses are offered on MAXWAVE configurations, so the lens that faces the dirt is the one built for it.

Cleaning head

On the MW-LC portables the handheld head weighs under 0.75 kg, because operators hold it through a full job on site.

Power Supply, Electrical System and Reinforced Cabinet

The power supply feeds the laser source and controls for every hour the machine runs. Available configurations use Mean Well power supplies, chosen for steady supply. Published output figures:

<1.5%Power stability, MW-LCW continuous, 25 °C over 2 h
<5%Power instability, MW-LY pulsed line
Electrical system
Schneider contactors, breakers and switching parts decide whether the machine starts cleanly every morning and shuts down safely when something trips.
Supply voltage
220 V MW-LY series · 380 V 3000 W MW-LCW · 24 V / 48 V MW-LC portables
Cabinet
MW-LCW reinforced configuration: 1.8 mm sheet metal with an A-grade paint finish, built for long shifts and moves between bays.
Wiring and status
Labelled wiring, so a circuit is traced by its label during maintenance and remote troubleshooting. A three-color alarm light shows a fault from across the bay.

Which options suit you depends on the line and the workload. Your engineer states the configuration in the quote, and it is recorded against your machine.

Schneider TeSys contactors inside a MAXWAVE laser cleaning machine cabinet
Schneider switching parts
Labelled wiring on the terminal rail of a laser cleaning machine
Every wire labelled
Coating thickness gauge checking the paint finish on a laser cleaner cabinet
Paint finish checked with a gauge
380 V main isolator switch on a continuous laser cleaning machine
380 V main isolator

Controlled Manufacturing in Six Fixed Stages

This is where MAXWAVE works as a laser cleaning machine manufacturer: every machine goes through one fixed order, and no stage is skipped or reordered.

  1. Incoming inspection

    Laser sources, optics, power supplies and electrical parts are checked on arrival, before they go into a machine.

  2. Mechanical assembly

    Cabinet or case, laser source mounting, fiber routing and cleaning head.

  3. Electrical installation

    Power supply, electrical components and wiring, installed and labelled.

  4. Software configuration

    Control system set up for the model: cleaning modes, scan patterns and the process library where they apply.

  5. Commissioning

    First power-up and first run; functions brought into working order.

  6. Final testing

    The six tests below, on the finished machine.

Fiber laser source in its shipping box at incoming component inspection
Laser source at incoming inspection
Inside a fiber laser source: driver boards and routed wiring
Driver boards and routed wiring

Faults are caught where they are cheapest to fix

A wrong part is stopped at incoming inspection, before it is built into a cabinet. A wiring fault shows up at commissioning, before the machine reaches final testing.

Your start-up is the machine's second start

Software configuration means the machine arrives set up for its model, with modes and scan patterns in place. Commissioning means the first power-up and first run happen in the MAXWAVE facility, not in your workshop.

Six Final Tests on Every Finished Machine

Final testing is done on the finished machine you ordered. Each test checks one thing that would otherwise surface in your workshop.

TestWhat is checkedWhat it protects for you
Laser output powerOutput the machine delivers is measuredA 300 W unit cleans like a 300 W unit from its first job
Operating stabilityOutput watched over a runThe last part of the shift comes out like the first
Pulse parametersPulse settings against the model's range (pulsed units)Controlled heat input, so thin sheet and precision parts do not discolor or warp
Optical componentsHead optics and protective lens inspectedA flaw is replaced before shipment instead of after a service call
Cooling systemChiller circuit on MW-LCW; airflow on air-cooled unitsThe laser source, the most expensive part, stays at working temperature
Equipment performanceControls, scan functions and modes run togetherThe machine works as a whole, not part by part

Swipe the table sideways

  • 13 to 500 ns pulse width; up to 3000 kHz, or 4000 kHz on LY400 and LY500
  • MW-LCW: six cleaning modes and the process library
  • MW-LC: 14 scan patterns and wireless phone control
MW-LCW continuous laser cleaning machine running its final equipment performance test
MW-LCW on its final run

Talk to an Engineer about how a test applies to your model.

Finished MW-LCW laser cleaning machine on the factory floor, ready for buyer inspection
The unit you ordered, before packing

Pre-Shipment Inspection and Remote Video Inspection

You can check the final tests yourself, in either of two ways, before the machine leaves.

Pre-shipment inspection

You or an inspection agent you appoint see the machine before it is packed: the unit, its configuration and how it runs.

Remote video inspection

The MAXWAVE team runs your machine on camera: output, settings screen and the cleaning head at work, without travelling.

In either route, ask to see any of the six final tests run on your unit.

Both happen before export packaging: what you inspect is what goes into the crate.

Test Equipment on the Inspection Bench

Two items of test equipment appear in the factory photographs, as they sit in the test area.

Fluke thermal imager
Shows surface temperature across a machine as a picture, so hot spots on a running unit are visible at a glance.
Fujikura fiber cleaving and fusion splicing
The cleaver cuts the fiber end flat and the fusion splicer joins fiber ends: both are part of handling the fiber that carries the laser to the cleaning head.
Fluke thermal imager used to check running laser cleaning machines
Fluke thermal imager
Fujikura FSM-100P+ fusion splicer on the inspection bench
Fujikura fusion splicer
Fiber cleaving equipment clamps on the test bench
Fiber cleaving clamps

Export Packaging for Laser Cleaning Machines

Each machine is packed for export after inspection, in four parts.

  • CushioningFoam around the machine body
  • Secure fixationThe machine cannot move inside the crate
  • Component protectionCleaning head and optics protected separately
  • Handling labelsHow forwarders and warehouses lift and store it
Export packaging: foam cushioning filling the gaps around a machine in a wooden crate
Export packaging: cushioningGaps around the machine filled with foam
Export packaging: machine stretch-wrapped and fixed to a pallet base
Export packaging: wrap and fixationStretch film and a fixed pallet base
Export packaging: closed wooden export crate with steel latches
Export packaging: closed crateLatched wooden crate, ready for labels

The machine arrives in the condition you inspected.

Packed after the final tests and your inspection
MAXWAVE branded flight case for shipping a portable laser cleaner
Portable units travel in their own flight case

International Shipping Coordination

The shipment is coordinated from the MAXWAVE facility to your country, so you know where the machine is and when to prepare your site for installation.

  • Shipping arrangementsTransport from the facility to your country
  • Export documentsThe documentation that travels with the machine
  • TrackingWhere the shipment is, and when to get the site ready

Tracking tells you when to prepare the site. Power, fume extraction and the Class 4 work area: support and maintenance.

After-Sales Support and Customer Equipment Records

After-sales starts with the paperwork that ships with the machine and continues through its working life.

Ships with the machine

  • Installation instructions
  • Operating tutorials
  • Maintenance videos, including safe setup

When something goes wrong

  • Remote engineering guidance
  • Troubleshooting
  • Spare parts supply

Your machine, kept on file

When you ask for a part or for help, engineers start from your exact unit, not a general model.

Line
As quoted
Power level
As quoted
Fitted options
As built
Configuration
As tested

Training, maintenance and remote support day to day: support and maintenance.

Galvo cleaning head with its optic, covered by the maintenance videos
Routine optic care is in the maintenance videos
Gloved operator holding a laser cleaning head during setup
Operating tutorials cover grip and setup

The entity on your quote is the entity on the documents.CE attestations · ISO 9001 certificate · trademark 66902017 · all Wuhan Maxwave Laser Technology Co., Ltd.

CE Machinery Directive Attestations for MAXWAVE Models

The CE attestations are issued under the Machinery Directive: a UDEM attestation under Machinery Directive 2006/42/EC and a Beide Machinery Directive attestation. Both list MAXWAVE laser cleaning machine models.

For an importer or distributor: the model on your quote can be matched to a model named on the attestation, and the holder named there is the company that sells you the machine.
UDEM Machinery Directive 2006/42/EC attestation of conformity for MAXWAVE laser cleaning machinesUDEM · 2006/42/EC Beide Machinery Directive verification of compliance listing laser cleaning machine modelsBeide · Machinery Directive
ISO 9001 quality management system certificate of the laser cleaning machine supplier Wuhan Maxwave Laser TechnologyZTC · ISO 9001 quality management system

ISO 9001 Quality Management System

Wuhan Maxwave Laser Technology Co., Ltd. operates an ISO 9001 quality management system. The company works to documented, audited procedures, and that is how the fixed manufacturing order and the final tests on this page run the same way on every order.

  • DocumentedThe six manufacturing stages are written procedure
  • AuditedProcedures are checked by the certification body
  • RepeatedSame order and same tests on every machine
MAXWAVE trademark registration certificate number 66902017Registration 66902017

MAXWAVE Trademark Registration 66902017

MAXWAVE is a registered trademark held by Wuhan Maxwave Laser Technology Co., Ltd.

For distributors and resellers: the brand on the machine and on your quotes is a registered mark held by the same company that issues the machine's documents.

The same mark is fitted on the front name plate of the cabinet and printed on the trolley and flight cases, so the unit your customer receives carries the brand named on the certificate and on every quote.

MAXWAVE name plate on a laser cleaning machine cabinet
The registered mark, as fitted on the cabinet

Assembly, Commissioning and Test Area

These photographs show where the seven systems happen: rows of machines going through the manufacturing stages, and the test area with its inspection equipment. All are photographs of the MAXWAVE facility.

  • Assembly hallMachines wait along the wall between mechanical assembly and electrical installation.
  • Commissioning benchThe first power-up and first run happen here, before final testing.
  • Test areaFiber cleaving and splicing equipment sits beside the thermal imager.
Assembly hall of the laser cleaning machine supplier with machines lined up along the wall
Assembly hall
Technician assembling a laser machine on the assembly floor
Mechanical assembly
Technician at the commissioning and test bench
Commissioning bench
Fiber handling equipment lined up in the test area
Fiber handling in the test area

Three Ways to Work With MAXWAVE

  • Direct purchase

    Plants, maintenance companies, contractors and mold shops

    Send your cleaning job, an engineer recommends a configuration, and you receive a quote for it. The line, power level and options named in the quote are what gets built, tested, inspected by you and kept on record.

    Send your requirement
  • Distributor and OEM cooperation

    Companies reselling laser cleaning equipment in their market

    Each machine you resell carries the same CE attestations, quality system and MAXWAVE trademark described above.

    OEM and wholesale
  • Custom systems

    Parts and lines that need a purpose-built setup

    Robot-assisted or large-part cleaning, designed around the part and run through the same tests.

    Custom laser cleaning system
Alloy wheel after laser cleaning with a MAXWAVE machine
Every route starts from a part like this

Send Your Cleaning Requirement

Use the form and an engineer recommends a configuration for your job. Include:

  • Material and thickness
  • Contamination: rust, paint, coating, oxide, oil or other residue
  • Area and workload: part size and surface cleaned per day or week
  • Application: production, maintenance, weld preparation, mold cleaning or contract work
  • Country of use
  • Photos of the part and the layer to remove

Phone / WhatsApp: +86 15327155363 · Call

Wuhan Maxwave Laser Technology Co., Ltd.Floor 1-2, Building B8, Leisure and Business Center, 28th Street, Panlongcheng Economic Development Zone, Huangpi District, Wuhan, Hubei, China